ioLogik R1200 Series

Features and Benefits

Dual RS-485 remote I/O with built-in repeater
Supports the installation of multidrop communications parameters
Install communications parameters and upgrade firmware via USB
Upgrade firmware through an RS-485 connection
Wide operating temperature models available for -40 to 85°C (-40 to 185°F) environments

Overview

The ioLogik R1200 Series RS-485 serial remote I/O devices are perfect for establishing a cost-effective, dependable, and easy-to-maintain remote process control I/O system. Remote serial I/O products offer process engineers the benefit of simple wiring, as they only require two wires to communicate with the controller and other RS-485 devices while adopting the EIA/TIA RS-485 communication protocol to transmit and receive data at high speed over long distances. In addition to communication configuration by software or USB and dual RS-485 port design, Moxa’s remote I/O devices eliminate the nightmare of extensive labor associated with the setup and maintenance of data acquisition and automation systems. Moxa also offers different I/O combinations, which provide greater flexibility and are compatible with many different applications.

Easy-to-Use Software Interface for Easy Maintenance

With Moxa’s easy-to-use ioSearch software, you can quickly access all of an ioLogik R1200 device’s status information and settings with a user-friendly graphical user interface. Furthermore, ioSearch also provides an easy method for updating firmware for all ioLogik R1200 devices over an RS-485 network, so you can even update your firmware remotely. The free and easy-to-use ioSearch software reduces the maintenance time and labor required to set up your communication interface. When more than one ioLogik R1200 are on the same RS-485 network, you no longer need to turn hundreds of dials during setup. Instead, simply configure and duplicate each ioLogik R1200’s baudrate and mode through the graphical user interface. This convenient software feature reduces maintenance engineers’ effort, and greatly simplifies upgrading your device’s configuration compared with more traditional methods.

Innovative Hardware Design Reduces Deployment Effort and Enhances Maintenance Efficiency

With the industry’s first RS-485 serial remote I/O with USB design, Moxa provides an innovative solution for upgrading and configuring RS-485 remote I/O communication devices and firmware. All you need to do is upload the configurations to a USB drive, plug it into the field device, and all the configurations and firmware updates will upload to the field device automatically.

Cost-Saving Hardware Design for Backup and Redundancy

Moxa’s ioLogik R1200 Series provides dual RS-485 ports so that when one of your RS-485 ports is damaged, you can quickly switch to the other RS-485 port for quick testing or repair. RS-485 remote I/O devices are already considered a low-cost technology, but with dual RS-485 ports, Moxa helps you save a little bit more. With the ioLogik R1200, you can take advantage of our dual RS-485 ports to set up wiring, provide computer redundancy, or back up your network using two computer topologies. For wiring redundancy, when your computer detects that one of the RS-485 connections is not responding, it can quickly switch over to the other RS-485 line to guarantee continuous communication between field sensors and the central computer. Furthermore, users have the freedom to define the settings. For computer redundancy, the ioLogik R1200 provides system operators with a secure backup when one system goes down.

Specifications

Input/Output Interface

Buttons

Reset button

Analog Input Channels

ioLogik R1240 Series: 8

Analog Output Channels

ioLogik R1241 Series: 4

Configurable DIO Channels (by software)

ioLogik R1212 Series: 8

Digital Input Channels

ioLogik R1210 Series: 16
ioLogik R1212 Series: 8
ioLogik R1214 Series: 6

Isolation

3k VDC or 2k Vrms

Relay Channels

ioLogik R1214 Series: 6

Digital Inputs

Connector:

Screw-fastened Euroblock terminal

Counter Frequency:

2.5 kHz

Digital Filtering Time Interval:

Software configurable

Dry Contact:

On: short to GND
Off: open

I/O Mode:

DI or event counter

Points per COM:

ioLogik R1210/R1212 Series: 8 channels
ioLogik R1214 Series: 6 channels

Sensor Type:

Dry contact
Wet Contact (NPN or PNP)

Wet Contact (DI to COM):

On: 10 to 30 VDC
Off: 0 to 3 VDC

Digital Outputs

Connector:

Screw-fastened Euroblock terminal

Current Rating:

200 mA per channel

I/O Mode:

DO or pulse output

I/O Type:

Sink

Pulse Output Frequency:

5 kHz

Over-Current Protection:

0.65 A per channel @ 25°C

Over-Temperature Shutdown:

175°C (typical)
150°C (min.)

Over-Voltage Protection:

45 VDC (typical)

Relays

Breakdown Voltage

500 VAC

Connector

Screw-fastened Euroblock terminal

Contact Current Rating

Resistive load: 5 A @ 30 VDC, 250 VAC, 110 VAC

Contact Resistance

100 milli-ohms (max.)

Electrical Endurance

100,000 operations @ 5 A resistive load

Initial Insulation Resistance

1,000 mega-ohms (min.) @ 500 VDC

Mechanical Endurance

5,000,000 operations

Pulse Output Frequency

0.3 Hz at rated load

Type

Form A (N.O.) power relay

Note

Ambient humidity must be non-condensing and remain between 5 and 95%.
The relays may malfunction when operating in high condensation environments below 0°C.

Analog Inputs

Accuracy

ioLogik R1240:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 to 60°C
ioLogik R1240-T:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 to 60°C
±0.5% FSR @ -40 to 75°C

Built-in Resistor for Current Input

120 ohms

Connector

Screw-fastened Euroblock terminal

I/O Mode

Voltage/Current

I/O Type

Differential

Input Impedance

10 mega-ohms (min.)

Input Range

0 to 10 VDC
0 to 20 mA
4 to 20 mA
4 to 20 mA (with burn-out detection)

Resolution

16 bits

Sampling Rate

All channels: 12 samples/sec
Per channel: 1.5 samples/sec
Only one channel enabled: 12 samples/sec

Analog Outputs

Accuracy

ioLogik R1241:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 to 60°C
ioLogik R1241-T:
±0.1% FSR @ 25°C
±0.3% FSR @ -40 to 75°C

Connector

Screw-fastened Euroblock terminal

Output Range

0 to 10 VDC
0 to 20 mA
4 to 20 mA

Resolution

12-bit

Voltage Output

10 mA (max.)

Load (Current Mode)

Internal power: 400 ohms (max.)
24 V external power: 1000 ohms (max.)

LED Interface

LED Indicators

Serial Interface

Baudrate

1200 bps to 921.6 kbps

Connector

Terminal block

No. of Ports

Parity

None
Even
Odd

Pull High/Low Resistor for RS-485

1 kilo-ohm
150 kilo-ohms

Serial Standards

RS-485

Stop Bits

1, 2

Surge

1 kV

ESD

15 kV

Data Bits

Flow Control

None
XON/XOFF

Serial Signals

RS-485-2w

Data+, Data-, GND

Serial Software Features

Industrial Protocols

Modbus RTU Server (slave)

Power Parameters

Power Connector

Screw-fastened Euroblock terminal

No. of Power Inputs

Input Voltage

12 to 48 VDC

Power Consumption

ioLogik R1210 Series: 154 mA @ 24 VDC
ioLogik R1212 Series: 187 mA @ 24 VDC
ioLogik R1214 Series: 207 mA @ 24 VDC
ioLogik R1240 Series: 216 mA @ 24 VDC
ioLogik R1241 Series: 343 mA @ 24 VDC

Physical Characteristics

Housing

Plastic

Dimensions

27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in)

Weight

200 g (0.44 lb)

Installation

DIN-rail mounting
Wall mounting

Wiring

I/O cable, 16 to 26 AWG
Power cable, 12 to 24 AWG

Environmental Limits

Operating Temperature

Standard Models: -10 to 75°C (14 to 167°F)
Wide Temp. Models: -40 to 85°C (-40 to 185°F)

Storage Temperature (package included)

-40 to 85°C (-40 to 185°F)

Ambient Relative Humidity

5 to 95% (non-condensing)

Altitude

2000 m

Standard and Certifications

EMC

EN 55032/24

EMI

CISPR 32, FCC Part 15B Class A

EMS

IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 0.5 kV
IEC 61000-4-5 Surge: Power: 2 kV
IEC 61000-4-6 CS: 3 V
IEC 61000-4-8 PFMF

Safety

UL 508

Shock

IEC 60068-2-27

Vibration

IEC 60068-2-6

Declaration

Green Product

RoHS
CRoHS
WEEE

MBTF

Time

1,239,293 hrs

Standards

Telcordia SR332

Warranty

Warranty Period:

ioLogik R1214: 2 years
ioLogik R1210/R1212/R1240/R1241 Series: 5 years

Models